Категории
Новые продукты
LDC-100 скалыватель оптических волокон большого диаметра * Применимо к волокнам диаметром 80~600 мкм *Вакуумный насос с V-образной канавкой удобно класть волокно *Прочное лезвие, срок службы более 20000 раз *Хранение данных 4000 групп * Удобное графическое меню, простое в эксплуатации Больше
S-22 Многожильный сварочный аппарат для оптоволокна Первый полностью автоматический многоядерный сварочный аппарат F iber Fusion в Китае _ _ _ Больше
Поляризация поддерживая (PM) в волокна splicer сплавливания с-12 * Ядра к ядру согласование, низкие потери сплайсинга * Наблюдение Endview и профиль и выравнивание * Автоматическая калибровка дуги и сплайсинга * ПМ волокна 45 и 90 градусов регулировка Больше
S-37 LDF Специальный сварочный аппарат для сварки волокон SHINHO S-37 — это последняя модель, которую мы разработали, она может сращивать оптические волокна диаметром от 125 до 400 мкм с низкими потерями при сращивании. Мы оснастили машину 3 различными держателями волокна и 2 парами запасных электродов. Больше
сердечник для выравнивания волокон сращиватель x900 сварочный аппарат с шестью двигателями, настоящая технология центровки сердечника. Сплайсинг 6 с, нагрев 16 с, автоматическое определение типов волокон. используется для wan / man / телекоммуникационных проектов. Больше
Надежный многофункциональный дуговой сварочный аппарат S16 Прочный промышленный дизайн, противоударный, пыленепроницаемый и водонепроницаемый. многофункциональный держатель для оголенного волокна, патч-кордов, кабеля и т. д. быстрое соединение и нагрев, автоматическая калибровка дуги. Больше
Термостриппер SHINHO X-18 для ленточных волокон Термостриппер Shinho X-18 — это недавно разработанный ручной термостриппер, специально разработанный для неразрушающего термозачистки оболочки ленточного кабеля до 12 волокон. Хороший и надежный инструмент для сращивания ленточных волокон. Больше
Высокоточный скалыватель оптических волокон X-50D Небольшой размер и легкий вес, прост в эксплуатации. Высокая точность и стабильная работа. Срок службы лезвия более 48000 раз, длина скола волокна 5 ~ 20 мм. Материал высокого качества Больше
Why Your Fusion Splicer is Mission Critical in Fiber Laser Repairing Work
1.What Does This "Fiber Splicer" Actually Fix?
Broken Wires (Fibers): Inside the laser, super-thin glass fibers carry the light. These can snap during handling, get bent too far, or get damaged by heat or dirt. You can't just plug them back together like an extension cord deep inside. The splicer cuts out the bad piece and permanently welds in a new section of matching fiber, making the light path whole again with almost no loss.
Replacing Worn-Out Parts: Lasers have special protective tips (like end caps) on their output fibers. If these get damaged or stop working well, the whole laser suffers. The splicer carefully welds the laser's internal fiber onto a brand-new replacement tip, which is a very precise job.
Adding New Bits: Sometimes a repair means putting in a new part, like an isolator (which stops harmful light reflections). These parts have their own little fiber tails. The splicer welds these tails directly onto the laser's existing fibers, making a strong, low-loss connection inside the machine.
2.Why is Welding Fibers Better Than Other Ways?
Almost No Power Loss: Every bit of light matters in a laser. A good fiber weld loses way less light power than any connector you could screw on.
Stops Harmful Reflections: Reflected light bouncing back inside a laser is bad news – it can make the laser unstable or even damage it. A clean fiber weld creates much less reflection than connectors.
Super Strong & Reliable: Once welded and protected with a sleeve, the joint becomes incredibly strong. It handles vibration and heat changes inside the laser much better than connectors that could come loose or get dirty over time. It's a permanent fix.
Fewer Weak Spots: Welding means fewer connection points inside the laser where things could potentially go wrong later.
3.The Bottom Line for Fixing Lasers:
If you work on fiber lasers, a good fusion splicer isn't just a nice-to-have tool; it's absolutely necessary. You simply can't do reliable, high-quality repairs on these machines without one.
It delivers the strong, low-loss, low-reflection connections that keep the laser running powerfully, efficiently, and reliably after the repair.
Investing in a quality fusion splicer and learning how to use it well is fundamental for any team serious about fixing fiber lasers quickly and getting them working like new again. When the laser stops, this "fiber splicer" is your best choice.
Следующая :
Fusion splicing operation© Авторское право: SHINHO OPTICS LIMITED Все права защищены.